APD ESC Configurator

Device Information

Model

—

Serial Number

—

Firmware Date

—

Family

HV-FOC

Connect your APD HV-FOC ESC via USB. The tool will retrieve its settings on connection. Use the tabs above to configure settings, then click Write Settings to save to the ESC.

Drive Settings

Drive Mode

Output Mode

Motor Direction

Setpoint Ramp Rates

Ramp rates limit your setpoint rate of change. Acceptable range: 10% per second (slow) – 1000% per second (fast).

Acceleration

% per Second

Deceleration

% per Second

Soft Start

Soft-start further limits the setpoint ramp rates when starting from zero. Acceptable range: 1–20 Seconds.

Enabled

Duration

Seconds

Under Voltage

At this point, the controller will no longer increase output power.

Under Voltage Limit

Volts

Other Limits

Temperature Limit

50–130°C

Capacity Limit (mAh)

Up to 99,000 (0 to bypass)

In the event that the above limits are reached, the controller will respond in the selected way.

Limiting Behaviour

1–30 Sec.

If gradual ramp down is selected, this is the time taken to ramp down from 100% to 0%.

Ramp Down Duration

Bus Current

Bus Current Limit

1–350 Amps (DC)

Regen Current Limit

0 – -350 Amps

Phase Currents

Phase Current Limit

1–500A (Vector sum of Iq and Id) Peak

Q-Axis Current

1–500 Amps

D-Axis Current

1–500 Amps Peak

Absolute Maximums

In the event that the PI controllers lose regulation, the controller will shutdown if these thresholds are exceeded.

Bus Current

1–500A (DC)

Phase Current

1–500A (RMS)

Motor Parameters

Resistance (mΩ)

Inductance (µH)

Motor Pole Pairs

RPM/Volt Constant (KV)

Flux Linkage (mWb)

Pole Pairs is the number of magnets divided by two. If your flux linkage is unknown, leave it at 0.

Hall Sensor Config

Hall Sensor Direction

Hall Sensor Offset (degrees)

Direction:
1 → Increase in motor angle = increase in hall angle.
-1 → Inverse relationship.

Offset:
Range: 0–360°. Angular offset between hall sensor angle and motor phase angle.

Speed Controller Gains

Proportional Gain

Integral Gain

Current Controller Gains

Proportional Gain

Integral Gain

Integrator Anti Wind Up

Only applies to RPM control, when using two controllers to drive a single motor.

DeadZone (RPM)

Gain K

Trapezoidal

Timing Advance

Modulation

Topology

Modulation

PWM Frequency

Hz

Bridge Dead-Time (nS)

100nS - 2000nS

Signalling

Input Signal Type

CAN Node ID

Endpoint Type (For PWM Only)

Detection

Lower

1000–1250 µS

Upper

1850–2000 µS

Deadzone (%)

1–10% (Bidirectional only)

Endpoint to RPM Mapping

If RPM control is used, the ESC will linearly map your input throttle to the desired setpoints. eRPM equals: Mechanical RPM × Motor Pole Pairs.

0% throttle mapped to

RPM

100% throttle mapped to

RPM

Motor Beep

The motor will beep once every 10 seconds indicating the ESC is armed and ready.

Enable

Motor Braking

Brake On Stop

Applies the magnetic motor brake when drive is off.

Arming

Bypass Zero Throttle Requirement

Upon ESC reboot or loss of drive signal, the ESC will no longer require a zero throttle value to arm the motor.

Position Sensor

If your controller is equipped with a sensor, this will enable the sensor homing routine upon receiving a FULL POWER command on boot up.

Position Sensor Alignment

Sensor Error

Other

Square Root Input (RPM mode only)

Synchronous Rectification (AFW)

Enable PWM RPM Output

Interval (Time between samples)

Disabled

25 milliSeconds

50 milliSeconds~ 2 hours of logged data

100 milliSeconds~ 4 hours of logged data

1 Second~ 40 hours of logged data

5 Seconds~ 400 hours of logged data

Log Management

To flash firmware, first put the ESC into DFU mode. Then connect to the DFU device over USB. Select a firmware file (.bin or .hex) and click Flash and Verify.

1 — Enter DFU Mode

Send the DFU command via serial to reboot the ESC into its bootloader.

2 — Connection

DFU Device Status

Not Connected

Connect to the STM32 DFU device over USB.

3 — Firmware File: *.hex *.bin accepted

Firmware File Path

No Firmware Selected

Size

—

Select a .bin or .hex firmware file.

4 — Firmware Flashing

Progress

0 Bytes Written

Status

Idle

Erase, flash and verify the firmware.